Failure Mode and Effects Analysis, which prioritizes different sources of error, is used in _________________ stage.
-
Define
-
Measure
-
Improve
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 18:09:182021-10-14 18:09:18Failure Mode and Effects AnalysisIn critical path method, earliest start is the:
-
The largest Earliest Finish leading to that task
-
The smallest Earliest Finish leading to that task
-
Average of Earliest Finish leading to that task
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 17:52:362021-10-14 17:52:36critical path methodTypically in a cause and effect diagram, the ______________ is used for classification of causes in the service industry.
-
5Ms
-
8Ps
-
5Ss
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 17:49:342021-10-14 17:49:34cause and effect diagramEffective quality control results in:
-
Increase in customer satisfaction
-
Lower cost
-
None of the above
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 17:45:512021-10-14 17:45:51quality controlFor a Poisson distribution:
-
The mean is greater than the variance
-
The mean is less than variance
-
The mean is equal to the variance
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 17:43:462021-10-14 17:43:46Poisson distributionWhich of the following is the correct combination of specifications while designing a control chart:
-
Sample size, Frequency of sampling, specification limit
-
Sample size, Frequency of sampling, Number of defects
-
Sample size, Specification limit, process standard deviation
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 17:40:462021-10-14 17:40:46control chartFor a process which is six sigma complaint, the percentage of products within specifications is:
-
95.20%
-
99.73%
-
99.10%
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 05:16:532021-10-14 05:16:53six sigmaA fan blade is specified by length and thickness. While sampling, it was found that for one particular blade, the length was non-conforming while the thickness was as per specifications. Should the blade be considered non-conforming for construction of a p chart?
-
Yes
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 04:51:482021-10-14 04:51:48non-conforming
Lot tolerance percent defective (LTPD) is a level of lot quality specified by the ______________.
-
Consumer
-
Producer
-
Supplier
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 04:42:362021-10-14 04:42:36LTPDIn a six sigma improvement project the least experienced individuals are:
-
Green Belt
-
Black belts
-
Red Belts
-
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
0
0
Bill
https://businessmanagementassignment.com/wp-content/uploads/2021/07/LOGO2.png
Bill2021-10-14 04:38:022021-10-14 04:38:02six sigma improvement project